===================================
Non Funtional Requirements
===================================

.. req:: label
   :id: REQ_INT3_1733080468
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The system should allow the pins to react to changes between high and low in no more than 10 microseconds.


.. req:: label
   :id: REQ_INT3_1733080497
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The system should respond in 1 microsecond when setting a pin.


.. req:: label
   :id: REQ_INT3_1733080522
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The system should allow input pins for reading signals to check inputs at least 10000 times per second.


.. req:: label
   :id: REQ_INT3_1733080548
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The system should make the pins consume less than 1 microampere when in low power mode.


.. req:: label
   :id: REQ_INT3_1733080584
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The pins should not exceed 1 milliampere of power when in use.


.. req:: label
   :id: REQ_INT3_1733080607
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The pins should be able to switch on and off at least 10 million times.


.. req:: label
   :id: REQ_INT3_1733080635
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The pins should work well at temperatures between -40°C to +85°C.


.. req:: label
   :id: REQ_INT3_1733080661
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The GPIO pins should be able to handle signals of up to 5V.


.. req:: label
   :id: REQ_INT3_1733080682
   :status: Draft
   :date-released:
   :priority: Low
   :submitted-by: Tarik Sinanovic
   :modified-by:
   :category: Non Functional
   :safety-asil: 
   :references: 
   :verification-and-validation: 

   The GPIO pins must go into low-power mode when not in use.